| |
Chevrolet Automotive Tools Wanted • Kent-Moore • 1930s 1940s |
|
| |
|
|
| |
The automotive tools listed here were made by the Kent-Moore Organization, Inc. of Detroit, Michigan in the 1930s and 40s for service work on General Motors cars and trucks. I am always happy to buy or trade for these or similar Kent-Moore automotive tools made for use on Chevrolet cars and trucks of the 1930s and 40s. I'm easy to work with, open to change, and totally respectful of your personal style. If you have old Kent-Moore automotive tools for sale or trade, please contact me. I look forward to hearing from you. |
|
| |
|
|
| |
Chevrolet Kent-Moore "T" Tools Wanted
|
|
| |
| |
|
Tool ID |
|
Description |
 |
|
T-19-4 |
|
Propeller Shaft Bushing and Oil Seal Replacer
1934-39 1 1/2 Ton Trucks (Bushing Only) |
|
|
| |
|
|
| |
T-19-4 Propeller Shaft Bushing and Oil Seal Replacer
At the outer end of the torque tube is a propeller shaft bushing. This tool is designed to replace the bushing to the correct depth in the tube without damage. The tool is made hollow to telescope over the end of the propeller shaft, and provides a safe way to replace the bushing and oil seal in the propeller shaft housing. (See also J-968, K-428, K-455, Propeller Shaft Bushing and Oil Seal Replacer). |
|
| |
|
|
| |
|
|
| |
|
|
| |
| |
|
Tool ID |
|
Description |
 |
|
T-120C |
|
Bushing Puller Set
T-120-1 Puller Screw
T-120-2 Puller Screw
T-120-3 Driver
T-120-4 Screw Center for Det. 1
J-1452-2B Handler for Center Screw used with Det. 1
|
|
|
| |
|
|
| |
|
|
| |
|
|
| |
| |
|
Tool ID |
|
Description |
 |
|
T-126R |
|
Crankshaft Gear Puller
1934-46 Passenger Cars and Trucks
T-126-1 Head
T-126-2 Cap Screws—5/16" x 3 3/8" Spec. (2 Required)
T-126-3R Screw
T-126-9R Screw End in J-1725 Set
|
|
|
| |
|
|
| |
T-126R Crankshaft Gear Puller
The crankshaft timing gear is a drive fit on the end of the crankshaft as well as being held in place with a key. To remove the timing gear without damage, a puller such as T-126R is necessary. The puller is easily and quickly attached to the gear holes by means of two threaded screws. The large puller screw is turned against the end of the crankshaft withdrawing the gear as it is turned. |
|
| |
|
|
| |
|
|
| |
|
|
| |
| |
|
Tool ID |
|
Description |
 |
|
TR-278R |
|
Differential Bearing Puller Set
All Models—All Years
J-1659-1 Handle
K-228-1 Fingers (2 Required)
TR-278R1 Puller
TR-278R2 Plug—1 1/8" Pilot
TR-278R3 Plug—1 1/2" Pilot
TR-278R4 Plug—1 1/4" Pilot
TR-278R5 Plug—1 21/32" Pilot
TR-278R6 Block
TR-278R10 Screw
TR-278-4 Clamp
TR-278-8 Rivet 1/4" x 1"
TR-278-9 Thumb Screw
Groove Pin—5/16" dia. x 1 3/4"—Type Number 2 (2 Req'd)
|
|
|
| |
|
|
| |
|
|
| |
|
|
